{{ 'fb_in_app_browser_popup.desc' | translate }} {{ 'fb_in_app_browser_popup.copy_link' | translate }}

{{ 'in_app_browser_popup.desc' | translate }}

The world's finest instrument collection "Only the best is good enough for us'

Welcome To

The world's finest instrument collection "Only the best is good enough for us'

Welcome To

The world's finest instrument collection "Only the best is good enough for us'

Creation Solderless Patch Cable Kit (12 ft / 16 plugs)

Creation Solderless Patch Cable Kit (12 ft / 16 plugs)

Solderless Kit (12 ft / 16 plugs)
Total 8pcs can be made.


全店,a

{{ productService.variationPriceMemberTag(variationSelected) }}
{{shoplineProductReview.avg_score}} {{'product.product_review.stars' | translate}} | {{shoplineProductReview.total}} {{'product.product_review.reviews' | translate}}
{{amazonProductReview.avg_rating}} {{'product.product_review.stars' | translate}} | {{amazonProductReview.total_comment_count}} {{'product.product_review.reviews' | translate}}
{{ title.name_translations | translateModel }} : {{variationName[$index] | translateModel}}
數量
一次最大商品購買數量限制為 99999
該數量不適用,請填入有效的數量。
售完

商品存貨不足,未能加入購物車

您所填寫的商品數量超過庫存

{{'products.quick_cart.out_of_number_hint'| translate}}

{{'product.preorder_limit.hint'| translate}}

每筆訂單限購 {{ product.max_order_quantity }} 件

現庫存只剩下 {{ quantityOfStock }} 件

若想購買,請聯絡我們。
商品描述
送貨及付款方式
顧客評價
商品描述

Looking for an affordable solderless system that is simple to make and looks great too? Done. No more stripping cable and wondering if you did it right. Just cut, insert, and screw the cap. That's it. 

Specs:
- Cable is 4mm in Diameter
- Braided Shield
- Stranded Copper Center
- Capacitance - 80pf per Meter (roughly 26pf per foot)

What's Included:
16 Creation Solderless Right Angle Plugs
12 feet of cable

You will need:
- Something to cut the cable clean (cable cutter, scissors, box cutter)
- Small Phillips screwdriver

Instructions:
Step 1:
Cut your cable to length with a very clean, straight cut (not at an angle) being careful not to flatten the cable as you cut it. 
(If the cable does become flattened, simply roll it between your fingers back into it's original roundness.

Step 2:
Insert the cable into the plug until you feel it stop against the pin inside. Then give it a moderately firm push so the pin pushes into the center of the cable.

Step 3:
Bend the cable into the notch and place the cap over the cable and plug. Align the hole for the set screw and then thread the screw into the opening. Screw firmly until the screw stops, but don’t over tighten. 

Step 4:
Be sure to test each cable as you complete them versus assembling your entire board. If the cable tests correctly, Huzzah! Now enjoy your cable that you made yourself. And be sure to send us photos of your completed board or tag us on Social Media.

Troubleshooting:
The solderless system works by using a pin inside the plug. This pin goes into the middle of the center wire of the cable for your signal connection and when assembled the set screw breaks through the outer layer to make contact with the ground. 

More than likely if your cable is not functioning properly 1 of 3 issues has occurred.
1. Either it's a problem with the cable itself by not being cut straight up and down, or being too flattened when pushed in. 

Check steps 1 and 2. 
2. The cable may not have been pushed in firmly enough, or it is possible to push too firmly. 
3. The screw may need to be tightened more or it’s possible it was over tightened. 

送貨及付款方式

送貨方式

  • International Shipping
  • 荔枝角門市自取(每日12:00-20:30)
  • 辦公室/住宅地址直送 (經順豐速運)

付款方式

  • 信用卡付款
  • Apple Pay
  • 微信支付
顧客評價
{{'product.product_review.no_review' | translate}}

相關產品